To be able to use the full range of Shopware 6, we recommend activating Javascript in your browser.

For architects

Software

Parameterise, configure and make individual settings. On this page, you can get software packages for JUNG KNX devices that are no longer available in the current product range.

KNX Smart Panel 5

The Smart Panel is parameterised and put into operation using the Smart Panel Designer. This configuration software is an executable Windows program that has to be installed independently of the ETX on the PC before first use. Among other things, it enables graphical project design of display and operating elements.

The configuration software can be run in Windows operating systems.

SP 5.1 KNX

Combined with data base version 1.0.4.0.vd5

Demo project for SP5.1 KNX

Project file to import into the Smart Panel Designer project design tool for SP5.1KNX.

ETS data base version 1.0.4.0.vd5

An ETS product data base is available with an embedded plug-in to compare the planning data for the ETS project (group addresses, visible communication objects) and the configuration software.

KNX Smart Panel 9

The Smart Panel is parameterised and put into operation using the Smart Panel Designer. This configuration software is an executable Windows program that has to be installed independently of the ETX on the PC before first use. Among other things, it enables graphical project design of display and operating elements.

The configuration software can be run in Windows operating systems.

SP 9.1 KNX and SP 9 KNX

An ETS product data base is available with an embedded plug-in to compare the planning data for the ETS project (group addresses, visible communication objects) and the configuration software.

Facility Pilot visualisation software

Attention! When using Windows 7, Windows 8 or 8.1 and Windows 10 (in each case 32 or 64 bit), the Falcon driver is a requirement from version 2.1.

When using the current Falcon driver on old Smart Pilot devices, a bus connection is only possible via USB or serial connection. To use the KNXNetIP connection, the following is necessary:

subsequent installation of the: Microsoft .NET Framework 2.0 Service Pack 2 (NetFx20SP2_x86.exe. Load the file directly from the Microsoft home page).
In the current setup, .NET 3.5 is already installed. .NET 2.0 SP2 is included.

FAP 3.6.2

FAP Software-Update Windows® 7 embedded (SPK10/15/19FAPVDSW from SN 10141395)
FAP Planner-3
FAP 50-3
FAP 300-3
FAP-FULL-3

Update of the FAP versions on the devices:

Smart Pilot SPK10/15/19FAPVDSW

only for devices with Windows® 7 embedded from SN 10141395

Including prepared switch surfaces for integrating the Siedle door communication on operating systems from Windows 7 (complete integration of the Siedle door communication in preparation).

Attention!

Not suitable for the update from FAP2 to FAP3
Not suitable for KNX Flat Panel PC 15" ref.-no.: PCT 15 FAPV (discontinued since 2009)

Visualisation Server 2.3.4.6

Only in connection with Facility Pilot from version 3.6.2, not for client version. Enables HTML5 visualisation of the JUNG GUI controls (on Firefox, Safari and Chrome in the respective current version). Facility Pilot V 3.6.2 must already be installed before installing the VisServer.

Can only be used on hardware with Windows 7 Home, Professional and Ultimate (32 and 64 bit), Windows 8 and 8.1 Pro (32 and 64 bit), and Windows 10 (32 and 64 bit) operating systems.

Depending on the system installation, the Internet information service may need to be activated in the Control Panel (see Visualisation Server Help, Chapter 2.6).

Attention!

The VisServer CANNOT be installed on the panels from the PCT...FAPVD, SP...FAPVD and SP9FAPVE ranges!
Not suitable for updating from previous versions to the FAPV-SERVER-REG.

Before running the installation, unpack the ZIP directory!

Change history

FAP 3.6.2 client

Update of Facility Pilot Client from version 3.04 to version 3.6.2 German

Visualisation Server help

Short description for FAP VisServer and Navigator

FAPV-SERVER-REG

Update of the Facility Pilot software of the FAPV-SERVER-REG to version 3.6.2 and update of the visualisation server to version 2.3.4.6

REG-FAPV-DE-BasisUndServerUpdate-3.6.2-180130.zip:
- batch to update the FAP-VisServer to version 2.3.4.6, and the FAP base software to version 3.6.2
- only suitable for FAPV-SERVER-REG DEUTSCH

Note: to run the update, deactivate write protection of the device. Unpack the content of the ZIP file and run REG-FAP-Update-3.6.2.bat. After the update, reactivate the write protection.

The update is not suitable for hardware other than the JUNG item FAPV-SERVER-REG!!
It leads to unusable software on other systems!!

Sample projects can be found at General downloads/Sample projects.
http://www.jung.de/musterprojekt

FAP 3.6.2 and VisServer 2.3.4.6

Copy update files to the FAPV-SERVER-REG, unpack them and start them.

Facility Pilot Navigator planning software

Version 2.3 – setup for new installation and update of previous versions

The application is executed as a client-server system (port 8081).
Please note the system requirements:

Windows 7 Home, Professional and Ultimate (32 and 64 bit), Windows 8 and 8.1 Pro (32 and 64 bit), Windows 10 (32 and 64 bit)

For using the application, an HTML5-enabled browser is required

New installation: the product runs in demo mode after installation. In order to use the full functionality, an activation will have to be purchased. To obtain a suitable licence, please use the software licence sale at www.jung.de.

Update: if you already own a previous version of the Faciliity Pilot Navigator, an update of your system to version 2.3 can be carried out using the setup file.

Attention!

Before running the installation, unpack the ZIP directory!

Facility Pilot Navigator planning software

Smart Pilot FAP
Facility Pilot software update Windows® XP embedded

Update of the Facility Pilot Software of the Smart Pilot FAP to version 3.6.2 and update of the visualisation server to version 2.3.4.3

Divus-WinXPEmbedded-DE-BasisUndServerUpdate-3.6.2-170413.zip:
- batch to update the FAP-VisServer to version 2.3.4.3, and the FAP base software to version 3.6.2
- only suitable for Smart Pilot FAP in German

Note: to run the update, unpack the content of the ZIP file and
run the 3.6.bat. Follow the instructions.

The update is not suitable for hardware other than the JUNG item Smart Pilot FAP in German with Windows® XP embedded!

FAP 3.6.2 and VisServer 2.3.4.6

Copy the update files to the Smart Pilot FAP with Windows XP embedded, unpack them there and run them.

Sample template colour touch panel

FP701CTIP layout tool

Creation of individual templates and adaptation of existing templates. Export of the image data as a bitmap image. The image can then be integrated in the colour touch panel IP.

Sample project

Project template to import into the colour touch panel IP. Adapting the template with the ETS3. Importing of images possible with the layout tool. Based on the colour touch panel IP software1v03.
Version 1.1

KNX product data bases

Technical downloads

To the downloads