KNX LED universal dimming actuator, 4-gang, rail mounting device, 4 rail units, Secure

39004 1S R

4 x 225 W, HV LED lamps typ. 4 x 1 ... 35 W (leading edge phase control), 4 x 1 ... 200 W (trailing edge phase control)
1 x 855 W
rail mounting device, 4 rail units
with manual electronic operation and LED status indication
project design and commissioning with ETS5 or a more recent version
ETS product family: Illumination
Product type: Dimmer

Intended use

Switching and dimming of incandescent lamps, HV halogen lamps, dimmable HV LED lamps, dimmable compact fluorescent lamps, dimmable inductive transformers with LV halogen or LV LED lamps, dimmable electronic transformers with LV halogen or LV LED lamps
Mounting on DIN rail according to EN 60715 in distribution box

Product characteristics

Outputs can be operated manually, construction site mode
Feedback in manual operation and in bus operation
Disabling of individual outputs manually or via bus
Status feedback
KNX Data Secure compatible with ETS 5.7.3 or higher
Can be updated with the ETS Service App

Dimming operation characteristic

Automatic or manual setting of the dimming principle suitable for the load
Protected against no-load, short-circuit and overheating
Signal in the event of a short-circuit, power failure and overload
Feedback of the switching position and the dimming value
Parameterisable switch-on and dimming behaviour
Time functions: switch-on delay, switch-off delay, staircase lighting timer with switch-off warning
Light scene operation
Status indication of the outputs via LED
Operating hours counter
Power failure longer than approx. 5 seconds causes the dimming outputs to switch off. Depending on the parameter setting, the connected load is calibrated after voltage return.
Increase in output power possible through parallel switching of multiple outputs
Power extension possible by means of amplifiers (ref.-no. ULZ 1755 REG)
Optional accessory: compensation module LED, ref.-no.: KM LED 230 U

Logic function characteristics

Logic gates
Transformer (conversion)
Disabling element
Comparator
Limit value switch

Read less... Read more...

Information

Article number:	39004 1S R
EAN/GTIN:	4011377179103

Read less... Read more...

Technical data

Rated voltage:	AC 110 ... 230 V ~
Mains frequency:	50/60 Hz
Power loss:	max. 7 W
Stand-by power:	approx. 0.16 W per channel
Ambient temperature:	−5 ... +45 °C
Storage/transport temperature:	−25 ... +70 °C
Lamp loads
Operating modes "universal", "leading edge phase control", "LED leading edge phase control"
Connected load, 230 V per output
Incandescent lamps:	20 ... 225 W
HV halogen lamps:	20 ... 225 W
If the operating mode for incandescent and HV halogen lamps is set to "leading edge phase control" or "LED leading edge phase control", the maximum connected load falls to 20 ... 210 W.
Inductive transformers:	20 ... 210 VA
Inductive transformers with LV LED:	20 ... 100 VA
Electronic transformers:	20 ... 210 W
Electronic transformers with LV LED:	20 ... 100 W
Dimmable HV LED lamps:	typical 1 ... 35 W
Dimmable compact fluorescent lamps:	typical 20 ... 80 W
Mixed load types
Capacitive-inductive:	not permitted
If the rated voltage is reduced to 110 V, the lamp loads are reduced to 50 %.
For inductive transformers and inductive transformers with LV LED, the operating mode "leading edge phase control" is not permitted.
Operating modes "trailing edge phase control", "LED trailing edge phase control"
Connected load, 230 V per output
Incandescent lamps:	20 ... 225 W
HV halogen lamps:	20 ... 225 W
Electronic transformers:	20 ... 225 W
Electronic transformers with LV LED:	20 ... 200 W
Dimmable HV LED lamps:	typical 1 ... 200 W
Dimmable compact fluorescent lamps:	typical 20 ... 150 W
If the rated voltage is reduced to 110 V, the lamp loads are reduced to 50 %.
Mounting width:	72 mm (4 rail units)
KNX
KNX medium:	TP 256
Commissioning mode:	S-mode
Rated voltage KNX:	DC 21 ... 32 V SELV
Current consumption KNX:	15 mA
Connection
Connection mode:	connection terminal
single wire:	1 x 0.5 ... 4 mm²
stranded without ferrule:	1 x 0.5 ... 4 mm²
stranded with ferrule:	1 x 0.5 ... 2.5 mm²

Read less... Read more...

Downloads

Show all downloads

Operating instructions	Select language Select language DE EN ES FR IT NL NO PT RU ZH
Product documentation	Select language Select language DE EN
Release notes	Select language Select language DE EN
Datenbank ETS5 + ETS6 Secure	Select language Select language DE EN ES FR IT NL RU
So wird's gemacht	Select language Select language DE EN
Update	Select language Select language DE EN
CAD (dwg)
CAD (stp)
EPLAN Makro
Tendering text	SG Select language Select language EN DE AT AE GB ES EE FR IT LT LV NL PL PT RU UA ZH
EC Declaration of Conformity	SG Select language Select language EN DE AT AE GB ES EE FR IT LT LV NL PL PT RU UA ZH
Product data sheet	SG Select language Select language DE AT EN AE GB US ES EE FR IT KR LT LV NL PL PT RU SE TR UA ZH